Figure 1. Steady-state shear stress a as a function of shear rate y in Sn-Pb alloy [10).

처리조건에서의 반고체유동의 수치모델링

David H. Kirkwood and Philip J. Ward
Department of Engineering Materials, University of Sheffield, Sheffield I UK

Keywords: semi-solid alloys, thixotropy, flow modelling.

Abstract

During the industrial process of semi-solid forming (or thixoforming) of alloy slurries, typically the operation of die filling takes around 0.1s.
During this time period the alloy slug is transformed from a solid-like structure capable of maintaining its shape, into a liquid-like slurry able
to fill a complex die cavity: this involves a decrease in viscosity of some 6 orders of magnitUde. Many attempts to measure thixotropic breakdown experimentally in alloy slurries have relied on the use of concentric cylindrical viscometers in which viscosity changes have been followed after shear rate changes over times above 1s to in excess of 1000 s, which have little relevance to actual processing conditions and therefore to modelling of flow in industrial practice. The present paper is an attempt to abstract thixotropic breakdown rates from rapid compression tests between parallel plates moving together at velocities of around 1mis, similar to industrial conditions. From this analysis, a model of slurry flow has been developed in which rapid thixotropic breakdown of the slurry occurs at high shear rates.

합금 슬러리의 반고체 성형 (또는 틱소 성형)의 산업 공정 동안, 일반적으로 다이 충진 작업은 약 0.1 초가 걸립니다.
이 기간 동안 합금 슬러그는 모양을 유지할 수있는 고체와 같은 구조에서 액체와 같은 슬러리로 변형됩니다.
복잡한 다이 캐비티를 채우기 위해 : 이것은 약 6 차의 마그 니트 점도 감소를 포함합니다. 합금 슬러리에서 실험적으로 요 변성 파괴를 측정하려는 많은 시도는 전단 속도가 1 초 이상에서 1000 초 이상으로 변화 한 후 점도 변화가 뒤 따르는 동심원 원통형 점도계의 사용에 의존하여 실제 가공 조건과는 거의 관련이 없습니다. 따라서 산업 현장에서 흐름 모델링에. 본 논문은 산업 조건과 유사하게 약 1mis의 속도로 함께 이동하는 평행 판 사이의 빠른 압축 테스트에서 요 변성 파괴 율을 추상화하려는 시도입니다. 이 분석으로부터 슬러리의 급속한 요 변성 분해가 높은 전단 속도에서 발생하는 슬러리 흐름 모델이 개발되었습니다.

Introduction

기존의 다이캐스팅을 위한 다이 설계는 과거에 예비 테스트 및 조정과 함께 축적 된 실무 경험의 문제였으며, 단기 실행, 랩, 다공성 등과 같은 결함을 제거하기 위해 다이 캐스트 제품을 검사했습니다. 이것은 모두 비용이 많이 드는 절차입니다.

시간과 비용, 그리고 프로세스의 컴퓨터 모델링은 이를 줄이거 나 없애기 위해 많은 운영자에 의해 개발되었습니다. 반고체 가공 (thixoforming)에서는 반고체 합금 슬러리의 전단이 내부 구조를 파괴하여 충전 작업 중 시간이 지남에 따라 점도가 낮아짐으로 발생하는 비 뉴턴 점도로 인해 모델링 문제가 더욱 어려워집니다.

시스템 전체에서 균일하지 않습니다. 충전 중에 발생하는 추가 응고로 인해 문제가 더욱 복잡해집니다. 빠른 충전으로 인해 이 단계에서 매우 작은 것으로 간주되기 때문에 현재 분석에서는 무시되었습니다.

우리 모델의 또 다른 한계는 슬러리가 균질한 물질로 거동 한다는 가정이며, 이는 어느 지점에서나 단일 점도로 설명될 수 있습니다. 이것은 빠른 전단의 고려 사항과 정상적인 요 변형성 조건 내에서 0.6 미만의 고형분을 분별하는 것으로 제한합니다.

<중략>……

Figure 1. Steady-state shear stress a as a function of shear rate y in Sn-Pb alloy [10).
Figure 1. Steady-state shear stress a as a function of shear rate y in Sn-Pb alloy [10).
Figure 2. Equilibrium viscosity as a function of shear rate in Sn-Pb alloy, fraction solid:0.36, fitted to Cross Model.
Figure 2. Equilibrium viscosity as a function of shear rate in Sn-Pb alloy, fraction solid:0.36, fitted to Cross Model.
Figure 3. Cheng Diagram: shear stress vs. shear rate.
Figure 3. Cheng Diagram: shear stress vs. shear rate.
Figure 4. Reciprocal of experimental breakdown time vs. y 1.3 for Sn-Pb alloy
Figure 4. Reciprocal of experimental breakdown time vs. y 1.3 for Sn-Pb alloy
Figure 5. Relaxation time, T, as a function of shear rate; see also figure 4, Fs =0.36.
Figure 5. Relaxation time, T, as a function of shear rate; see also figure 4, Fs =0.36.
Figure 6. Experimental and modelled results for compression test on AI-A356 alloy at two temperatures.
Figure 6. Experimental and modelled results for compression test on AI-A356 alloy at two temperatures.
Table 1. Calculated parameters for the breakdown in compression tests [20].
Table 1. Calculated parameters for the breakdown in compression tests [20].
Figure 7. Drop-forge results from Yurko and Flemings [7].
Figure 7. Drop-forge results from Yurko and Flemings [7].
Figure 8. Prediction of FLOW-3D®.
Figure 8. Prediction of FLOW-3D®.

Conclusions

y에서 전단 된 반고체 슬러리의 틱소 트로픽 분해에 대한 속도 방정식은 다음과 같은 형식으로 제안됩니다. T = l / (a ​​+ uym), 여기서 T는 급속 분해 또는 유사 정상 상태 구조에 대한 특성 시간이며, 밴드 m은 상수입니다. 이 관계는 제한된 범위의 전단 속도에서 Sn-Pb 합금의 전단 속도 점프에 의해 실험적으로 확인되었습니다.

이 파괴율 방정식은 AI-Si 합금의 반고체 슬러그에 대한 빠른 압축 테스트에서 실험적으로 얻은 힘-변위 곡선을 시뮬레이션하기 위해 FLOW-3D® (버전 8.2 : FlowScience Inc.)에 도입되었습니다. 담금 시간과 다른 압축 속도에서. 이 분석의 결과는 모든 경우에 요 변성 거동이 관련되어 있음을 나타내지만, 5 분 동안 담근 후 (산업 관행에서와 같이) 구조가 크게 분해되었으며 초기에는 낮은 전단 속도 영역에서 흐름이 뉴턴에 가깝습니다.

파괴율은 100 S-I 이상의 전단율에서 극적으로 증가하는 것으로 가정 됩니다. 이 예측은 높은 전단 속도에서 더 세심한 작업에 의해 테스트되어야 하지만 평균 전단 속도가 1300 sol까지 생성된 드롭 단조 실험에 의해 뒷받침되는 것으로 보입니다 [7].

References

[I] T.Y Liu, H.Y. Atkinson, PJ. Ward, D.H. Kirkwood: Metall.Mater.TransA, 34A (2003), 409/17.
[2] A. Zavaliangos and A. Lawley: J. Mater. Eng. Perfonn., 4 (1995),40/47.
[3] M.R. Barkhudarov, e.L. Bronisz, e.w. Hirt: ProcAth Int. Conf. onSemi-solid Processing of Alloys and Composites,1996, Sheffield,p.llO.
[4] W.R.Loue, M.Suery, J.L.Querbes: Proc.2ndInt.Conf.on Semi-solidProcessing of Alloys and Composites,1992, Cambridge MA , pp266-75.
[5] P.Kapranos, D.H.Kirkwood, M.R. Barkhudarov: Proc.5th Int. Conf.on Semi-solid Processing of Alloys and Composites, Golden, Colorado,1998. pp.II-19.
[6] T.Y. Liu, H.Y. Atkinson, P. Kapranos, D.H. Kirkwood, S.G. Hogg:Metall. Mater. Trans A, 34A (2003), 1545/54.
[7] J.A. Yurko and M.e. Flemings: Metall. Mater. Trans A, 33A (2002),2737/46.
[8] M. Modigell and J. Koke: Mechanics of Time Dependent Materials, 3(1999), 15/30.
[9] Y. Laxmanan and M.e. Flemings: Metall. Trans. A, IIA( 1980),1927/36.
[IO]A.R.A Mclelland, N.G. Henderson, H.Y. Atkinson, D.H. Kirkwood:Mater. Sci. Eng., A232 (1997), 110/18.
[II] H.A. Barnes: 1. Non-Newtonian Fluid Mech., 81 (1999),133n8.
[12]A.N. Alexandrou, E. Due , Y. Entov: 1. Non-Newtonian Fluid Mech.,96 (2001), 383/403.
[13]C.L. Martin, P. Kumar and S. Brown: Acta Mat. Mater., 42 (1994),3603/14.
[14]C. Quaak, L. Katgennan and W.H. Kool: Proc. 4th Conf. on Semi-solid Processing of Alloys and Composites, 1996, Sheffield, pp.35/39.
[15]D.C-H. Cheng: Int. Journal Cosmetic Science, 9 (1987), pp.151/91.
[16]An Introduction to Rheology: H.A. Barnes, J.F. Hutton and K Walters,Elsevier, Amsterdam, 1989.
[17]A.M. de Figueredo, A. Kato and M.e. Flemings: Proc.6th Int. Conf.on Semi-solid Processing of Alloys and Composites, 2000, Turin,477/82.
[18]1.y’ Chen and Z. Fan: Mater. Sci. Tech., 18 (2002), 237/42.
[19]Z. Fan: Int. Mater. Rev., 47 (2002), No.2, 49/85.
[20]D.H. Kirkwood and P.J. Ward: Proc. 8th Int. Conf. on Semi-solid Processing of Alloys and Composites, 2004, Cyprus. To be published.